After lots of debates, discussions, and queries, Xiaomi has rolled out the much-awaited Android Pie for Mi A1 device. As of now, it’s a software update that is limited to a closed community of users. Well, As it happens in the Android community the ROM was leaked in public. So, a lot of curious users installed it. Now, this has lead to trouble among a few users. Being the beta build, the software is apparently causing boot loop issue on Mi A1. A few users who reportedly installed the leaked ROM, are facing the bootloop on their respective Mi A1. However, this can be solved. In this post, we will tell you how to Fix Xiaomi Mi A1 Bootloop After Upgrading to Android 9 Pie Beta.

This solution was initially suggested by XDA member Gray911. So, props to him for finding this fix to the mi A1 boot loop issue. You must keep in mind that, this guide is only for solving the bootloop caused due to the installation of leaked Pie beta build. If you have a bootloop issue which is caused by something else, then this guide won’t help you at all. Basically, it’s a recovery process that will take you back to Android 8.1 Oreo.

Also Read

You can find the link below for the Android 8.1 Oreo fastboot ROM. You have to flash it using the TWRP. Also, you will need the Mi Flash Tool, which we have attached below.

How To Fix Xiaomi Mi A1 Bootloop After Upgrading to Android 9 Pie Beta

Before doing anything, you will need the Android 8.1 Oreo fastboot ROM, TWRP backup, Mi Flash Tool, and ADB Binary. You can get them in the Downloads section.

Downloads

Pre-Requisites

  • A PC/Laptop.
  • You must install Mi Flash Tool.
  • Make sure to install the ADB binary.
  • Install the TWRP.
  • Mi A1 must be on the leaked Pie beta build.

Note: Perform this process at your own risk. GetDroidTips will not be responsible for bricking of any devices while/after following this recovery procedure.

Steps To Perform the Recovery and Fix the Bootloop Issue on Xiaomi Mi A1

Step-1 Unzip the ADB binary zip file. From that, copy and paste the adb folder to the C drive where you have installed ADB on your PC

  • How to Install MIUI 12 Ported ROM for Xiaomi Mi A1 (Custom ROM)
  • Xiaomi Mi A1 Firmware Flash File
  • List Of All Best Custom ROM For Xiaomi Mi A1 [Updated]

Step-2 Unzip the TWRP zip file you have downloaded. You will see a folder named TWRP.

Step-3 Now Boot your Mi A1 into Fastboot mode by using Volume Down + Power button. Then connect it to PC using cable.

Step-4  Go to C:\ drive > Open the folder ‘ADB’.

Step-5 Open command window from there and type the following command.

fastboot boot recovery.img

Step-6  Now copy the folder‘TWRP’ and move it to the device storage.

Step-7 In the TWRP menu select ‘Restore’, > go to the backup folder > tap to restore ‘Boot’ and ‘EFS’ data.

In case you don’t see anything, go to TWRP > Backup > copy the folder “2018-12-06–15-41-27_PQ1A181205006” into “TWRP” folder.

Advertisement

Step-8 Again in the TWRP menu, select Reboot > tap Bootloader.

Step-9 Unzip the Android 8.1 Oreo fastboot ROM to any directory on your PC.

Step-10 Open Mi Flash tool > click the ‘Refresh’ button. Your phone will detect the tool.

Step-11 Click on the ‘Select’ button, browse and select the folder where all the ROM files were extracted earlier.

Step-12 Finally, click on the ‘Flash’ button. It will start flashing the v8.1 Oreo firmware update.

So, that’s it. After completing the installation, your phone will go back to its original state with Android 8.1 Oreo on-board. This will essentially

Source

Download and Install Official Lineage OS 19.1 for Xiaomi Mi A1